1. Concentricity ≤ 0.00024" at face and arbor
2. Pilot Diameter: 1-1/2", H5 pilot tolerance
3. Rear thread for pull stud is 1" - 8
4. Gage Length is 2-13/32"
1. T.I.R. ≤ 0.0002 at collet face
2. Through-spindle coolant capability
3. Balanced to G6.3 at 10000 rpm
4. Hardened and precision taper ground to AT3 accuracy
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 10,000 rpms
3. Works on all CAT50 Machines
4. Through-spindle coolant capability
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 10,000 rpms
3. Works on all CAT50 Machines
4. Through-spindle coolant capability
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 10,000 rpms
3. Works on all CAT50 Machines
4. Through-spindle coolant capability
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 10,000 rpms
3. Works on all CAT50 Machines
4. Through-spindle coolant capability
Made in Italy
IMS Part code: CAT40026X3.0
Made in Italy
IMS Part code: CAT40027X2.76
Made in Italy
IMS Part code: CAT40027X3.0
Made in Italy
IMS Part code: CAT40027X4.0
Made in Italy
IMS Part code: CAT40028X2.76
Made in Italy
IMS Part code: CAT40028X3.0
Made in Italy
IMS Part code: CAT40303X3.0
Made in Italy
IMS Part code: CAT40305X3.0
Made in Italy
IMS Part code: CAT40307X3.0
Made in Italy
IMS Part code: CAT40309X3.0
Made in Italy
IMS Part code: CAT40207X3.0
Made in Italy
IMS Part code: CAT40209X3.0
Made in Italy
IMS Part code: SCAT40327L3
Made in Italy
IMS Part code: CAT50305X4.0
Made in Italy
IMS Part code: CAT50307X4.0
Made in Italy
IMS Part code: CAT50027X4.0
Made in Italy
IMS Part code: CAT50028X4.0
Made in Italy
IMS Part code: BT40-ER32-70
Made in Italy
IMS Part code: BT40-ER20UM-70
Made in Italy
IMS Part code: BT40-ER16UM-63
1. Fits HSK63(A,B,C,D,E,F type) tool holder.
2. Solid casting structure and denser roller bearings to bite the tool holder, stronger and durable.
3. Easy to use, reduce the taper wear, improve the tool holder life and precision.
1. Adapter size: G3
2. Tap size: ANSI #5 (1/8")
3. Connection dia.: 0.748"
4. Tap shank square: 0.11" x 0.11"
5. Tap shank dia.: 0.141"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI #8 (5/32")
3. Connection dia.: 0.748"
4. Tap shank square: 0.131" x 0.131"
5. Tap shank dia.: 0.168"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI #10 (3/16")
3. Connection dia.: 0.748"
4. Tap shank square: 0.152" x 0.152"
5. Tap shank dia.: 0.194"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI 1/4"
3. Connection dia.: 0.748"
4. Tap shank square: 0.191" x 0.191"
5. Tap shank dia.: 0.255"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI 5/16"
3. Connection dia.: 0.748"
4. Tap shank square: 0.238" x 0.238"
5. Tap shank dia.: 0.318"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI 3/8"
3. Connection dia.: 0.748"
4. Tap shank square: 0.286" x 0.286"
5. Tap shank dia.: 0.381"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI 7/16"
3. Connection dia.: 0.748"
4. Tap shank square: 0.242" x 0.242"
5. Tap shank dia.: 0.323"
6. Torque control tapping can prolongs tool life
1. Adapter size: G3
2. Tap size: ANSI 1/2"
3. Connection dia.: 0.748"
4. Tap shank square: 0.275" x 0.275"
5. Tap shank dia.: 0.367"
6. Torque control tapping can prolongs tool life
1. Shank type: BT50
2. For use with tap collets G3
3. Projection length: 5-1/8"
4. Sleeve dia.: 1-27/32"
5. Connection hole dia.: 0.748"
6. Very accurate and durable
1. Shank type: BT40
2. For use with tap collets G3
3. Projection length: 4-21/64"
4. Sleeve dia.: 1-27/32"
5. Connection hole dia.: 0.748"
6. Very accurate and durable
1. Shank type: MT2
2. For use with tap collets G3
3. Projection length: 3-35/64"
4. Sleeve dia.: 1-27/32"
5. Connection hole dia.: 0.748"
6. Very accurate and durable
1. Shank type: MT3
2. For use with tap collets G3
3. Projection length: 3-35/64"
4. Sleeve dia.: 1-27/32"
5. Connection hole dia.: 0.748"
6. Very accurate and durable
1. Shank type: MT4
2. For use with tap collets G3
3. Projection length: 3-35/64"
4. Sleeve dia.: 1-27/32"
5. Connection hole dia.: 0.748"
6. Very accurate and durable
1. Hole size: 3/8"
2. Length from Datum line to nose end : 2.5"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. To clamp tools with 3/8"shank.
1. Hole size: 1/2"
2. Length from Datum line to nose end : 2-5/8"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. To clamp tools with 1/2" shank.
1. Hole size: 5/8"
2. Length from Datum line to nose end : 3-3/4"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. To clamp tools with 5/8"shank.
1. Hole size: 7/8"
2. Length from Datum line to nose end : 4"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. To clamp tools with 7/8"shank.
1. Hole size: 1"
2. Length from Datum line to nose end : 4"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. To clamp tools with 1"shank.
1. Hole size: 1/2" |
2. Length from Datum line to nose end : 4-5/8" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT50 |
6. To clamp tools with 1/2"shank. |
1. Hole size: 5/8" |
2. Length from Datum line to nose end : 3-3/4" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT50 |
6. To clamp tools with 5/8"shank. |
1. Hole size: 3/4" |
2. Length from Datum line to nose end : 5-3/4" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT50 |
6. To clamp tools with 3/4"shank. |
1. Hole size: 7/8" |
2. Length from Datum line to nose end : 5-3/4" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT50 |
6. To clamp tools with 7/8"shank. |
1. Hole size: 1" |
2. Length from Datum line to nose end : 6" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT50 |
6. To clamp tools with 1"shank. |
1. Hole size: 3/4" |
2. Length from Datum line to nose end : 1-3/8" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT40 |
6. To clamp tools with 3/4"shank. |
1. Hole size: 1" |
2. Length from Datum line to nose end : 1/16" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT40 |
6. To clamp tools with 1"shank. |
1. Hole size: 1-1/4" |
2. Length from Datum line to nose end : 2-1/8" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT40 |
6. To clamp tools with 1-1/4"shank. |
1. Inside taper: Morse taper 4.
2. Length from Datum line to nose end : 3.55"
3. Material: 20CrMnTi
4. T.I.R.: 0.0002"
5. Ourside taper CAT40
6. For Morse taper 4 tools with tang.
1. Hole size: 3/4" |
2. Length from Datum line to nose end : 3 3/4" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT40 |
6. To clamp tools with 3/4"shank. |
1. Hole size: 3/4" |
2. Length from Datum line to nose end : 2-1/2" |
3. Material: 20CrMnTi |
4. T.I.R.: 0.0002" |
5. Ourside taper CAT40 |
6. To clamp tools with 3/4"shank. |
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Constructed of alloy steel hardened to 56 – 60 HRC for long, durable service life
6. AT3 or better accuracy standard taper specification for maximum contact with spindle.
7. Nickel coating surface, Anti-rust, anti-corrosion, durability better.
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC for long, durable service life
6. AT3 or better accuracy standard taper specification for maximum contact with spindle.
7. Nickel coating surface, Anti-rust, anti-corrosion, durability better.
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 RPM
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8 UNC
5. Hardened to 56 – 60 HRC
6. Projection: 6"
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M12 x 1.75
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT30 Machines
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER16 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756" (70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER20 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER20 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756"(70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER25 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER25 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756" (70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 5-29/32" (150mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER40 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M24 x 3
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 7-7/8" (200mm)
5. Works on all BT50 Machines
6. Collet chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M24 x 3
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 9-27/32" (250mm)
5. Works on all BT50 Machines
6. Collet chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M24 x 3
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 7-7/8" (200mm)
5. Works on all BT50 Machines
6. Collet chuck accepts all ER40 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M12 x 1.75
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT30 Machines
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M12 x 1.75
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16"(100mm)
5. Works on all BT30 Machines
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M12 x 1.75
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16"(100mm)
5. Works on all BT30 Machines
6. Collet Chuck accepts all ER32 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756" (70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER16 collets
1. For deep hole machining
2. Shank is 3/4" diameter 4" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 4" length
3. Material: 20CrMnTi / JIS-SCM415, Surface
4. Made from alloy steel hardened to HRC 56-60
5. This tool holder accepts all ER16 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 5.51" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER16 collets
6. Run out≤: 0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 1.65" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC 56-60
5. This tool holder accepts all ER16 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 3.42" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER16 collets
6. Run out:≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 4" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER20 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 5.5" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER20 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 6" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER20 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 2" length
3. All critical tool holder surfaces precision ground
4. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER25 collets
6. Coolant through capability
7. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1/2" diameter, 5.51" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER16 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1" diameter 2" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER40 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1-1/2" diameter, 2.95" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER40 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1-1/4" diameter, 2.3" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC 56-60
5. This tool holder accepts all ER40 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1-1/4" diameter, 6.2" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC 56-60
5. This tool holder accepts all ER32 collets
6. Run out: ≤0.00008"
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20 CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8 UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Material: 20CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1" - 8UNC
5. Hardened to 56 – 60 HRC
1. For deep hole machining
2. Shank is 3/4" diameter 4" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER25 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 3/4" diameter 4.5" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER40 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 5/8" diameter 6.2" length
3. All critical tool holder surfaces precision ground
4. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Coolant through capability
7. Run out:≤0.00008"
1. For deep hole machining
2. Shank is 5/8" diameter 5.51" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Run out:≤0.00008"
1. For deep hole machining
2. Shank is 5/8" diameter, 2" length
3. All critical tool holder surfaces precision ground
4. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Coolant through capability
7. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 5/8" diameter 5.51" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC 56-60
5. This tool holder accepts all ER11 collets
6. Run out:≤ 0.00008"
1. For deep hole machining
2. Shank is 5/8" diameter, 2.36" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER16 collets
6. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1/2" diameter, 6.2" length
3. All critical tool holder surfaces precision ground
4. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Coolant through capability
7. Run out: ≤0.00008"
1. For deep hole machining
2. Shank is 1/2" diameter, 4" length
3. Material: 20CrMnTi / JIS-SCM415
4. Made from alloy steel hardened to HRC56-60
5. This tool holder accepts all ER11 collets
6. Run out: ≤0.00008"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB30 Machines
4. Rear thread for pull stud is 1/2"-13UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 1-3/4"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB30 Machines
4. Rear thread for pull stud is 1/2"-13UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 2.76"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB30 Machines
4. Rear thread for pull stud is 1/2"-13UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 2.76"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB30 Machines
4. Rear thread for pull stud is 1/2"-13UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 2.76"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB30 Machines
4. Rear thread for pull stud is 1/2"-13UNC
5.Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 1-3/4"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB40 Machines
4. Rear thread for pull stud is 5/8"-11UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC
6. Projection: 2-3/8"
1. TIR: ≤0.0002"
2. Material: 20CrMnTi
3. Works on all NMTB40 Machines
4. Rear thread for pull stud is 5/8"-11UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC for long, durable service life
6. Projection: 2-3/8"
1. Material: Allyed case hardened steel, black-finished and precisely grinding
2. Hardness: HRC 56-58
3. T.I.R: ≤0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 6"
6. Collet Chuck accepts all ER16 collets
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 4"
6. Collet chuck accepts all ER25 collet
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 3-3/8"
6. For 3/4" straight shank end mill
7. include 5/8-1 setscrews
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 2-1/2"
6. For 3/8" straight shank end mill
7. include 3/8-24 setscrews
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 2-1/2"
6. For 1/4" straight shank end mill
1. Material: Alloy case hardened steel, black-finishedand precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricityof the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 andB6339
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 4"
6. For 1" straight shank end mill
7. include 3/4-16 setscrews
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. TIR ≤ 0.0002"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 1-1/2"
6. Include heat-treated and coated carbon steel nut
1. CAT NO tapershank is in conformity with AT3 standard
2. Fittingtolerance H6 for straight sets
Model No. | D | L | Weight(kg) |
R8-FMA1" | 25.4 | 40 | 0.9 |
R8-FMA3/4" | 19.05 | 40 | 0.8 |
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Allyed case hardened steel, black-finished and precisely grinded
2. Hardness: HRC 56-58
3. Max. run out: <0.0001"
4. Carbon depth: 0.016" to 0.047"
5. Projection: 7.87"
6. Collet chuck accepts all ER32 collet
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339
1. Material: Alloy case hardened steel, black-finished
and precisely grinded.
2. Hardness: HRC 56-58
3. Carbon depth: 1/32" ± 1/64"
4. Runout: < 0.0002"
5. Concentricity
of the inner and outer cone: 0.0002"
6. Shank body standard: MAS 403 and
B6339