1. This set includes 10 individual ER16 collets in 1/32" increments.
2. The following sizes are included - 1/32,1/16,3/32,1/8,3/16,7/32,1/4,5/16,11/32,3/8"
3. Runout tolerance within 15 micron (0.00059") at 4×d position
4. Full set covers all collet sizes from 1/32" - 3/8" (0.031" - 0.375")
.75" x 3" Square Die 120 Degree for HTB-1000 | HTB-1000-SD753
1. Hole diameter: 0.118"(3mm) , overall length is 4"
2. High grade collet steel
3. Drawbar thread: 7/16" - 20
4. Good elasticity, high precision, run-out tolerance 0.0012"
1. Hole diameter: 1", overall size: 35 x 52mm / 1-3/8" x 2-3/64" (Max.D*L)
2. Good elasticity, high precision, run-out tolerance 0.00059"
3. Using high quality spring steel is stable in perfomance
4. These collets conform to DIN 6388 standards
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 1/2"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 1/4"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 3/4"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 3/8"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 5/16"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1"
3. Inside dia.: 5/8"
4. Length under head: 2-3/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Hole diameter: 1" (25.4mm), overall length is 4" (101.6mm)
2. High grade collet steel
3. Drawbar thread: 7/16" - 20
4. Good elasticity, high precision, run-out tolerance 0.0012"
1. Threaded Mount: 1-1/2" - 18 TPI
2. Shank diameter 1" (25.4mm)
3. Hardened and precision ground
4. Made of high grade alloy steel
1. 1" Straight Shank, 3 Jacobs Taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1" straight shank, 4 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1" straight shank, 6 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. Shank diameter: 1", arbor diameter: 1"
2. Runout: .00031" TIR, H5 arbor tolerance
3. Works with tool holder
4. Hardened and precision taper ground
1. 1" straight shank, 2 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1" x 4" Square Die 120 Degree for HTB-1000 | HTB-1000-SD14
1" X 6" Square Die 240 Degree for HTB-1000
1. Type: Z
2. Outside dia.: 1-1/2"
3. Inside dia.: 1"
4. Length under head: 3-1/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 1"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LB
2. Outside dia.: 1-1/2"
3. Inside dia.: 1-1/4"
4. Length under head: 3-1/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 1-1/4"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/2"
3. Inside dia.: 1/2"
4. Length under head: 3-1/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LB
2. Outside dia.: 1-1/2"
3. Inside dia.: 1/2"
4. Length under head: 3-1/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 1/2"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/4"
4. Length under head: 3-1/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LB
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/4"
4. Length under head: 3/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/4"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/8"
4. Length under head: 3-1/4"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LB
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/8"
4. Length under head: 3-1/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 3/8"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LB
2. Outside dia.: 1-1/2"
3. Inside dia.: 5/8"
4. Length under head: 3-1/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: LBF
2. Outside dia.: 1-1/2"
3. Inside dia.: 5/8"
4. Length under head: 3-5/32"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/4"
3. Inside dia.: 1"
4. Length under head: 3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/4"
3. Inside dia.: 1/2"
4. Length under head: 2-5/8"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/4"
3. Inside dia.: 3/4"
4. Length under head: 3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/4"
3. Inside dia.: 3/8"
4. Length under head: 3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-1/4"
3. Inside dia.: 5/8"
4. Length under head: 3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Threaded mount: 1-1/2" - 18 TPI
2. Shank diameter: 1-1/4" (32mm)
3. Hardened and precision ground
4. Made of high grade alloy steel
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 1"
4. Length under head:3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 1"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 1-1/2"
4. Length under head:3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 1-1/2"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 1-1/4"
4. Length under head:3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 1-1/4"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 1/2"
4. Length under head:3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 1/2"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 3/4"
4. Length under head:3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 3/4"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: J
2. Outside dia.: 1-3/4"
3. Inside dia.: 5/8"
4. Length under head: 3"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1. Type: Z
2. Outside dia.: 1-3/4"
3. Inside dia.: 5/8"
4. Length under head: 3-1/2"
5. Precision 0.0004" TIR
6. Concentricity: 0.0002"
1.25" x 5" Round Die 120 Degree Radius for HTB-1000-RD1255-120
1.25" x 5" Square Die 120 Degree Radius for HTB-1000-120
1.5" x 5" Square Die 120 Degree for HTB-1000 | HTB-1000-SD155
1.5" x 6" Square Die 120 Degree for HTB-1000 | HTB-1000-SD156
1.5" x 6" Square Die 240 Degree for HTB-1000 | HTB-1000-SD156-240
1.Mill Diameter (D):1.5 / 1/16" |
2.Length of Cut (I):4 / 3/16" |
3.Shank Diameter (d): 4 / 3/16" |
4.Overall Length (L):50 / 2" |
5. WorkMaterial:Solid carbide End Mill, Alloy Steel, Die Steel, Heat Treatment HRC45~HRC68. |
6. Coating: Blue NB, Good at high speed cutting high head cutting.For dry cutting. |
7. Carbide Material:Super Micro Grain 0.3u m/m Co 8%. |
1. Hole diameter: 1/16" (1.59mm), overall length is 4" (101.6mm)
2. High grade collet steel
3. Drawbar thread: 7/16" - 20
4. Good elasticity, high precision, run-out tolerance 0.0012"
No return,no refund after purchase
1. Mount Type: JT33 Mount
2. Runout: .003in TIR.
3. Key Style: keyless
4. Clamping Range: 1/32"-12" (0.5-13mm)
1. Mount Type: JT6 Mount
2. Runout: .003in TIR.
3. Key Style: keyless
4. Clamping Range: 1/32"-12" (0.5-13mm)
1. Mount type: threaded mount
2. Runout: 0.004" TIR
3. Clamping range: 1/32" - 1/2"
4. Chuck key included
1. Hole diameter: 1/2", overall size: 35 x 52mm / 1-3/8" x 2-3/64" (Max.D*L)
2. Good elasticity, high precision, run-out Tolerance 0.00059"
3. Using high quality spring steel is stable in perfomance
4. These OZ collets conform to DIN 6388 standards
1. Hole diameter: 1/2" (12.7mm), overall length is 4" (101.6mm)
2. High grade collet steel
3. Drawbar thread: 7/16" - 20
4. Good elasticity, high precision, run-out tolerance 0.0012"
No return,no refund after purchase
1. Hole diameter: 1/2", overall length is 1-7/32" (31mm)
2. Material: high-grade 65Mn
3. Clamping range: 15/32" - 1/2" (0.461" - 0.500")
4. Total runout less than .00031 on these precise ER20 collets
1. Hole diameter: 1/2", overall length is 1-3/8" (35mm)
2. Material: high-grade 65Mn
3. Clamping range: 15/32" - 1/2" (0.461" - 0.500")
4. Total runout less than .00031 on these precise ER25 collets
1. F1 TYPE BORING HEAD SET
2. Max offset: 5/8''
3. Boring bar dia: 1/2''
4. Min graduation: 0.001''
5. Contact shank: R8
6. Shank connect TPI: 7/8''-20
1. 1/2" straight shank, 0 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1/2" straight shank, 1 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1/2" straight shank, 2 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1/2" straight shank, 3 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1/2" straight shank, 33 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. 1/2" straight shank, 6 jacobs taper
2. Hardened and precision ground
3. Made of high grade alloy steel
4. Total indicated runout is from 0.00059" to 0.00079"
1. Shank diameter: 1/2", arbor diameter: 1/2"
2. Runout: 0.00031" TIR, H5 arbor tolerance
3. Works with tool holder
4. Hardened and precision taper ground
1. Shank diameter: 1/2", arbor diameter: 3/4"
2. Runout: 0.00031" TIR, H5 arbor tolerance
3. Works with tool holder
4. Hardened and precision taper ground
1. Material: 65Mn
2. Hardness: clamping part HRC55~60, elastic part HRC40~45
3. 29 PC Set
1. Mount Type:JT1 Mount
2. Runout: .003in TIR.
3. Key Style:keyless
4. Clamping Range: 1/32"-1/4" (0.5-6mm)
1. Hole diameter: 1/4", overall size: 35 x 52mm / 1-3/8" x 2-3/64" (Max.D*L)
2. Good elasticity, high precision, run-out Tolerance 0.00059"
3. Using high quality spring steel is stable in perfomance
4. These collets conform to DIN 6388 standards
1. Hole diameter: 1/4" (6.35mm), overall length is 4" (101.6mm)
2. High grade collet steel
3. Drawbar thread: 7/16" - 20
4. Good elasticity, high precision, run-out tolerance 0.0012"
No return,no refund after purchase
1. Hole diameter: 1/4", overall length is 1-7/32" (31mm)
2. Material: high-grade 65Mn
3. Clamping range: 7/32" - 1/4" (0.211" - 0.25")
4. Total runout less than .00031 on these precise ER20 collets
1. Hole diameter: 1/4", overall length is 1-3/8" (35mm)
2. Material: high-grade 65Mn
3. Clamping range: 7/32" - 1/4" (0.212" - 0.25")
4. Total runout less than .00031 on these precise ER25 collets
1. Threader: 1/4-20 N.C.
2. Tap Chamfer: Bottom
3. Shank Dia.: 1"
4. Material: HSS
5. Threader length: 2 1/2"
6. Thread Standard: ANSI
1. Threader: 1/4-20 N.C.
2. Tap Chamfer: Taper
3. Shank Dia.: 1"
4. Material: HSS
5. Threader length: 2 1/2"
6. Thread Standard: ANSI
1. Material: 65Mn
2. Hardness: clamping part HRC55~60, elastic part HRC40~45
3. 6 PC Set
1. Material: 65Mn
2. Hardness: clamping part HRC55~60, elastic part HRC40~45
3. 13 PC Set
1. Hole diameter: 1/8", overall size: 35 x 52mm / 1-3/8" x 2-3/64"(Max.D*L)
2. Good elasticity, high precision, run-out tolerance 0.00059"
3. Using high quality spring steel is stable in perfomance
4. These collets conform to DIN 6388 standards
1. Hole diameter: 1/8", overall length is 1-3/8" (35mm)
2. Material: high-grade 65Mn
3. Clamping range:3/32" - 1/8"(0.086" - 0.125")
4. Total runout less than .00031 on these precise ER25 collets
1. Mount Type:JT6 Mount
2. Runout: .003in TIR.
3. Key Style:keyless
4. Clamping Range: 1/8"-5/8" (1-16mm)
1. 10pc ER16 collet set : 1/32" - 3/8" by 32th (1/32,1/16,3/32,1/8,3/16,7/32,1/4,5/16,11/32,3/8)
2. All collets are made of high quality alloy spring steel 0.0005" accuracy
3. Hardened and precision ground
4. 1pc 3/4-ER16-3.94" collet chuck, 15PCS ER40 collets, 1pc ER40 spanner
5. Rear thread 3/8" - 16
6. Fitted plastic case
1. 10pc ER20 collet set : 1/32" - 3/8" by 32th (3/32",1/8",3/16",7/32",1/4",5/16",11/32",3/8",7/16",1/2")
2. All collets are made of high quality alloy spring steel 0.0005" accuracy
3. Hardened and precision ground
4. 1pc R8 collet chuck, 10PCS ER20 collets, 1pc ER20 spanner
5. Fitted plastic case
1. Table Diameter : 9-27/32" (250mm), Gear Ratio: 90:1
2. Diameter of Center Hole: 55/64" (22mm), Center Taper MT3
3. Height of center for Vert. mounting: 6-1/2" (165mm)
4. Number of T-Slot: 6, Width of T-Slot: 35/64" (14mm)
Bolton Tools
1.Mill Diameter (D):10 / 3/8" |
2.Length of Cut (I):30 / 1-3/16" |
3.Shank Diameter (d): 10 / 3/8" |
4.Overall Length (L):75 / 2-15/16" |
5.WorkMaterial:Solid carbide End Mill, Aluminum Alloys, Copper Alloys. |
6. Coating: Uncoated(Blank). |
7. Carbide Material:Micro Grain 0.6u m/m Co10%. |
1. Mill Diameter (D):10 / 3/8" |
2. Length of Cut (I):30 / 1-3/16" |
3. Shank Diameter (d): 10 / 3/8" |
4. Overall Length (L):75 / 2-15/16" |
5. WorkMaterial: Solid carbide end mill, General steel, carbon steel, alloy steel |
6. Coating:High lube Ti Si, Good for wet cutting. |
7. Carbide Material: Micro Grain 0.6u m/m Co10 %. |
1.Mill Diameter (D):10 / 3/8" |
2.Length of Cut (I):30 / 1-3/16" |
3.Shank Diameter (d): 10 / 3/8" |
4.Overall Length (L):75 / 2-15/16" |
5. WorkMaterial: Solid carbide End Mill, General steel, Pre-hardened steel, Stainless steels, Alloy steel. |
6. Coating: TX, Glass hard Ti Si. |
7. Carbide Material: High toughness Micro Grain 0.6u m/m Co10%. |
1.Mill Diameter (D):10 / 3/8" |
2.Length of Cut (I):25 / 1" |
3.Shank Diameter (d): 10 / 3/8" |
4.Overall Length (L):75 / 2-15/16" |
5. WorkMaterial:Solid carbide End Mill, Alloy Steel, Die Steel, Heat Treatment HRC45~HRC68. |
6. Coating: Blue NB, Good at high speed cutting high head cutting.For dry cutting. |
7. Carbide Material:Super Micro Grain 0.3u m/m Co 8%. |
1. Insert fits on all of our Shell Mills and End Mills 90 deg rectangle.
2. Corner radius is .016.
3. CSM35 grade is ideal for steel and stainless steel.
4. This insert has 2 cutting edges.
1. Insert fits on all of our Shell Mills and End Mills 90 deg rectangle.
2. Corner radius is .016.
3. CKM15 grade is ideal for cast iron.
4. This insert has 2 cutting edges.