1. Hole Diameter: 16mm (0.629"), overall length is 1.575”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 16-15mm (0.629"-0.590")
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 17mm (0.669"), overall length is 1.575”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 17-16mm (0.669"-0.629")
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 19mm (0.748"), overall length is 1.575”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 19-18mm (0.748"-0.708")
4. Hardness: 46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 20mm (0.787"), overall length is 1.575”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 20-19mm (0.787"-0.748")
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 2 mm ( 0.078" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2-1.5 mm ( 0.078"-0.059" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3 mm ( 0.118" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3-2 mm ( 0.118"-0.078" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4 mm ( 0.157" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4-3 mm ( 0.157"-0.118" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5 mm ( 0.196" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5-4 mm ( 0.196"-0.157" )
4. Hardness:4 6-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 6 mm ( 0.236" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 6-5 mm ( 0.236"-0.196" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 7 mm ( 0.275" ), overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 7-6 mm ( 0.275"-0.236" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 8 mm ( 0.314" ), overall length is 1.338”
2. Clamping Range: 8-7 mm ( 0.314"-0.275" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 9 mm ( 0.354" ), overall length is 1.338”
2. Clamping Range: 9-8 mm ( 0.354"-0.314" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 10 mm ( 0.394" ), overall length is 1.338”
2. Clamping Range: 10-9 mm ( 0.394"-0.354" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 11 mm ( 0.433" ), overall length is 1.338”
2.Clamping Range: 11-10 mm ( 0.433"-0.394" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 12 mm ( 0.472" ), overall length is 1.338”
2. Clamping Range: 12-11 mm ( 0.472"-0.433" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 13 mm ( 0.511" ), overall length is 1.338”
2. Clamping Range: 13-12 mm ( 0.511"-0.472" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 14 mm ( 0.551" ), overall length is 1.338”
2. Clamping Range: 14-13 mm ( 0.551"-0.511" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 15 mm ( 0.590" ), overall length is 1.338”
2. Clamping Range: 15-14 mm ( 0.590"-0.551" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 16 mm ( 0.629" ), overall length is 1.338”
2.Clamping Range: 16-15 mm ( 0.629"-0.590" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1 mm(0.039”), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1-0.5 mm ( 0.039”-0.019” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2 mm(0.078”), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2-1.5 mm ( 0.078”-0.059” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3 mm ( 0.118" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3-2 mm ( 0.118"-0.078" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4 mm ( 0.157" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4-3 mm ( 0.157"-0.118" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5 mm ( 0.196" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5-4 mm ( 0.196"-0.157" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 6 mm ( 0.236" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 6-5 mm ( 0.236"-0.196" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 7 mm ( 0.275" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 7-6 mm ( 0.275"-0.236" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 8 mm ( 0.314" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 8-7 mm ( 0.314"-0.275" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 9 mm ( 0.354" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 9-8 mm ( 0.354"-0.314" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 10 mm ( 0.394" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 10-9 mm ( 0.394"-0.354" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 11 mm ( 0.433" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 11-10 mm ( 0.433"-0.394" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 12 mm ( 0.472" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 12-11 mm ( 0.472"-0.433" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 13 mm ( 0.511" ), overall length is 1.240”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 13-12 mm ( 0.511"-0.472" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1 mm ( 0.039" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1-0.5 mm ( 0.039”-0.019” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2 mm ( 0.078" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2-1.5 mm ( 0.078”-0.059” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3 mm ( 0.118" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3-2 mm ( 0.118"-0.078" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4 mm ( 0.157" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4-3 mm ( 0.157"-0.118" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5 mm ( 0.196" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5-4 mm ( 0.196"-0.157" )
4. Hardness: 46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 6 mm ( 0.236" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 6-5 mm ( 0.236"-0.196" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 7 mm ( 0.275" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 7-6 mm ( 0.275"-0.236" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 8 mm ( 0.314" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 8-7 mm ( 0.314"-0.275" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 9 mm ( 0.354" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 9-8 mm ( 0.354"-0.314" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 10 mm ( 0.394" ), overall length is 1.082”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 10-9 mm ( 0.394"-0.354" )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1 mm ( 0.039" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1-0.5 mm ( 0.039”-0.019” )
4. Hardness:46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 1.5 mm ( 0.059" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1.5-1 mm ( 0.059”-0.039” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2 mm ( 0.078" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2-1.5 mm ( 0.078”-0.059” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2.5 mm ( 0.098" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2.5-2 mm ( 0.098”-0.078” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3 mm ( 0.118" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3-2.5 mm ( 0.118”-0.098” )
4 . Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3.5 mm ( 0.137" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3.5-3 mm ( 0.137”-0.118” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4 mm ( 0.157" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4-3.5 mm ( 0.157”-0.137” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4.5 mm ( 0.177" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4.5-4 mm ( 0.177”-0.157” )
4. Hardness :46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5 mm ( 0.196" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5-4.5 mm ( 0.196”-0.177” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5.5 mm ( 0.216" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5.5-5 mm ( 0.216”-0.196” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 6mm ( 0.236" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 6-5.5 mm ( 0.236”-0.216” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 6.5 mm ( 0.256" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 6.5-6 mm ( 0.256”-0.236” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 7 mm ( 0.276" ), overall length is 0.708”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 7-6.5 mm ( 0.276”-0.256” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1 mm ( 0.039" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1-0.5 mm ( 0.039”-0.019” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 1.5 mm ( 0.059" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 1.5-1 mm ( 0.059”-0.039” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2 mm ( 0.079" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2-1.5 mm ( 0.079”-0.059” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 2.5 mm ( 0.098" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 2.5-2 mm ( 0.098”-0.079” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3mm ( 0.118" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3-2.5 mm ( 0.118”-0.098” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3.5 mm ( 0.138" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 3.5-3 mm ( 0.138”-0.118” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4 mm ( 0.157" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4-3.5 mm ( 0.157”-0.138” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 4.5 mm ( 0.177" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 4.5-4 mm ( 0.177”-0.157” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5 mm ( 0.196" ), overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 5-4.5 mm ( 0.196”-0.177” )
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/16", overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.0625"-0.0428"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 3/32", overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.0937”-0.0740”
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 1/8", overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.125"-0.085"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/16", overall length is 0.531”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.187"-0.148"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/32", overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.0937”-0.0740”
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 5/16", overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.312"-0.273"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/8", overall length is 1.338”
2. Material: High Grade JIS-SUJ2
3. Clamping range: 0.375" - 0.335"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out tolerance ≤ 0.0003"
1. Hole Diameter: ER40-23PCS(1/8“-1”), overall length is 1.811"
2. Clamping Range: 1/8"-1"
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER40-23PCS(4mm-26mm), overall length is 1.811"
2. Clamping Range: 4mm-26mm (0.157"-1.023")
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER32-18PCS(1/8"-3/4"), overall length is 1.575"
2. Clamping Range: 1/8"-3/4"
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER32-18PCS(3mm-20mm), overall length is 1.575"
2. Clamping Range: 3mm-20mm (0.118"-0.787”)
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER25-14PCS(1/8"-5/8"), overall length is 1.338"
2. Clamping Range: 1/8"-5/8"
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER25-15PCS(2 mm - 16 mm), overall length is 1.338"
2. Clamping Range: 2 mm - 16 mm( 0.078"-0.629" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER20-12PCS(3/32-1/2"), overall length is 1.240"
2. Clamping Range: 3/32"-1/2"
3.Material: High Grade JIS-SUJ2
4..Hardness:46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER20-13PCS(1-13mm), overall length is 1.240"
2. Clamping Range: 1mm-13mm(0.039"-0.512")
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER16-8PCS(1/8"-3/8"), overall length is 1.082"
2. Clamping Range: 1/8"-3/8"
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER16-10PCS(1-10mm), overall length is 1.082"
2. Clamping Range: 1-10 mm ( 0.039"-0.393" )
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: ER11-7PCS(1/16"-1/4"), overall length is 0.708"
2. Clamping Range: 1/16"-1/4"
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole diameter: ER11-7PCS (1mm-7mm), overall length is 0.708"
2. Clamping range: 1mm - 7mm (0.039" - 0.275")
3. Material: High Grade JIS-SUJ2
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/8", overall length is 1.20”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.125"-0.105"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/16", overall length is 1.20”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.187"-0.167"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/4", overall length is 1.20”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.25" - 0.23"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5/16", overall length is 1.20”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.312"-0.292"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/8", overall length is 1.20”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.375"-0.355"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/8", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.125"-0.105"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/16", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.187"-0.167"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/4", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.25"-0.23"
4.Hardness: 46-50HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5/16", overall length is 1.771”
2. Material: High Grade JIS - SUJ2
3. Clamping Range: 0.312" - 0.292"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 3/8", overall length is 1.771”
2. Material: High Grade JIS - SUJ2
3. Clamping Range: 0.375"- 0.355"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 7/16", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.437" - 0.417"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 1/2", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.50" - 0.48"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 9/16", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.562"- 0.542"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 5/8", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.625"-0.605"
4.Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
1. Hole Diameter: 17/32", overall length is 1.771”
2. Material: High Grade JIS-SUJ2
3. Clamping Range: 0.531" - 0.511"
4. Hardness: 46-50 HRC
5. Good elasticity, high precision, Run-Out Tolerance ≤ 0.0003"
◎ Hole Diameter: 1/8", overall length is 2.381”
◎ Clamping Range: 0.125"-0.105"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48
◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 9/64", overall length is 2.381”
◎ Clamping Range: 0.140"-0.120"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 5/32", overall length is 2.381”
◎ Clamping Range: 0.156"-0.136"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 11/64", overall length is 2.381”
◎ Clamping Range: 0.171"-0.151"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 3/16", overall length is 2.381”
◎ Clamping Range: 0.187"-0.167"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 13/64", overall length is 2.381”
◎ Clamping Range: 0.203"-0.183"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 7/32", overall length is 2.381”
◎ Clamping Range: 0.218"-0.198"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 15/64", overall length is 2.381”
◎ Clamping Range: 0.234"-0.214"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 1/4", overall length is 2.381”
◎ Clamping Range: 0.25"-0.23"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 17/64", overall length is 2.381”
◎ Clamping Range: 0.265"-0.245"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 9/32", overall length is 2.381”
◎ Clamping Range: 0.281"-0.261"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 19/64", overall length is 2.381”
◎ Clamping Range: 0.296"-0.276"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 5/16", overall length is 2.381”
◎ Clamping Range: 0.312"-0.292"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 11/32", overall length is 2.381”
◎ Clamping Range: 0.343"-0.323"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 3/8", overall length is 2.381”
◎ Clamping Range: 0.375"-0.355"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 7/16", overall length is 2.381”
◎ Clamping Range: 0.437"-0.417"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 1/2", overall length is 2.381”
◎ Clamping Range: 0.50"-0.48"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 9/16", overall length is 2.381”
◎ Clamping Range: 0.562"-0.542"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 5/8", overall length is 2.381”
◎ Clamping Range: 0.625"-0.605"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 11/16", overall length is 2.381”
◎ Clamping Range: 0.687"-0.667"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 3/4", overall length is 2.381”
◎ Clamping Range: 0.75"-0.55"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 13/16", overall length is 2.381”
◎ Clamping Range: 0.812"-0.992"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
◎ Hole Diameter: 7/8", overall length is 2.381”
◎ Clamping Range: 0.875"-0.855"
◎ Material: 42 CrMo
◎ Hardness : HRC 44-48◎ Good elasticity, high precision, Run-Out Tolerance ≤ 0.00059"
1. Hole Diameter: 1", overall length is 2.381”
2. Clamping Range: 1" - 0.98"
3. Material: 42CrMo
4. Hardness: HRC 44-48
5. Good elasticity, high precision, Run-Out Tolerance ≤0.00059"
1. ER25UM Collet Nut has an internal thread of M32 X 1.5 pitch
2. Outside diameter is 1.65" (42mm)
3. ER25UM Collet Nut holds all ER25 collets
4. ER25UM Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53HRC
1. ER40 Collet Nut has an internal thread of M50 X 1.5 pitch
2. Outside diameter is 2.48" (63mm)
3. ER40 Collet Nut holds all ER40 collets
4. ER40-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER32 Collet Nut has an internal thread of M40 X 1.5 pitch
2. Outside diameter is1.97" (50mm)
3. ER32 Collet Nut holds all ER32 collets
4. ER32-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER20UM Collet Nut has an internal thread of M25 X 1.5 pitch
2. Outside diameter is 1.37" (35mm)
3. ER20UM Collet Nut holds all ER20 collets
4. ER20-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER16UM Collet Nut has an internal thread of M22 X 1.5 pitch
2. Outside diameter is 1.30" ( 32 mm )
3. ER16UM Collet Nut holds all ER16 collets
4. ER16-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER25M Collet Nut has an internal thread of M30 X 1.0 pitch
2. Outside diameter is 1.37" ( 35 mm )
3. ER25M Collet Nut holds all ER25 collets
4. ER25M-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER20M Collet Nut has an internal thread of M24 X 1.0 pitch
2. Outside diameter is 1.10"(28mm)
3. ER20M Collet Nut holds all ER20 collets
4. ER20M-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20 CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER16M Collet Nut has an internal thread of M19 X 1.0 pitch
2. Outside diameter is 0.87" (22mm)
3. ER16M Collet Nut holds all ER16 collets
4. ER16M-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER11M Collet Nut has an internal thread of M13 X 0.75 pitch
2. Outside diameter is 0.63"(16mm)
3. ER11M Collet Nut holds all ER11 collets
4. ER11M-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER8M Collet Nut has an internal thread of M10 X 0.75 pitch
2. Outside diameter is 0.47" (12 mm)
3. ER8M Collet Nut holds all ER11 collets
4. ER8M-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER11A Collet Nut has an internal thread of M14 X 0.75 pitch
2. Outside diameter is 0.75" (19 mm)
3. ER11A Collet Nut holds all ER11 collets
4. ER11A-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER16A Collet Nut has an internal thread of M22 X 1.5 pitch
2. Outside diameter is 1.10" (28 mm)
3. ER16A Collet Nut holds all ER16 collets
4. ER16A-Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi.
7. Made from alloy steel hardened to 50-53 HRC
1. ER20A collet nut has an internal thread of M25 x 1.5
2. Outside diameter is 1.33" (34mm)
3. ER20A collet nut holds all ER16 collets
4. ER20A Wrench works on this collet nut
5. Balanced to 20000rpm at G2.5
6. Material: 20CrMnTi
7. Made from alloy steel hardened to 50-53HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Constructed of alloy steel hardened to 56 – 60 HRC for long, durable service life
6. AT3 or better accuracy standard taper specification for maximum contact with spindle.
7. Nickel coating surface, Anti-rust, anti-corrosion, durability better.
1. Standard cutting pipe diameter: 2"
2. Max. Machining Length: 4"
3. 3-phase 220V 60Hz
4. Dual-axis double servo system for positioning and cutting
5. Fast and repetitive cutting, suitable for mass production
6. Shorten cutting time and improve cutting efficiency
7. Processing range: 1-3/16" to 2-3/4" (need matched with different dies)
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Constructed of alloy steel hardened to 56 – 60 HRC for long, durable service life
6. AT3 or better accuracy standard taper specification for maximum contact with spindle.
7. Nickel coating surface, Anti-rust, anti-corrosion, durability better.
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8UNC
5. Hardened to 56 – 60 HRC
1. TIR: ≤0.0002"
2. Balanced to G6.3 at 18,000 RPM
3. Works on all CAT50 Machines
4. Rear thread for pull stud is 1"-8 UNC
5. Hardened to 56 – 60 HRC
6. Projection: 6"
1. TIR: ≤ 0.0002"
2. Balanced to G6.3 at 18,000 rpms
3. Works on all CAT40 Machines
4. Rear thread for pull stud is 5/8" - 11
5. Hardened to 56 – 60 HRC
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M12 x 1.75
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT30 Machines
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER16 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756" (70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER20 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 3-15/16" (100mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER20 collets
1. T.I.R. ≤ 0.00012"
2. Rear thread for pull stud M16 x 2
3. Balanced to 15000 RPM @ G6.3
4. Projection Length: 2.756"(70mm)
5. Works on all BT40 Machines
6. Collet chuck accepts all ER25 collets